Sharp AR-M550N Скачать руководство пользователя страница 364 | Manualshive

Страница: 364 / 460

Sharp AR-M550N Скачать руководство пользователя страница 364

AR-M550/M620/M700 SELF DIAG MESSAGE AND TROUBLESHOOTING 9 - 9

Main
code

Sub

code

Title

The entered account name of the
POP3 server or the password for
authentication is invalid.

CE

07

Phenomenon

Display

Lamp

Message

Details

The entered account
name of the POP3 server
or the password for
authentication is invalid.
POP3 server
authentication check
error

Section

Operation
mode

Note

Case 1

Trouble
position/
Cause

Improper connection of
the network cable

Remedy

Check connection of the
network cable.

Note

Case 2

Trouble
position/
Cause

Improper account name
or password registered in
the POP3 server

Remedy

Check that the account
name or the password
registered for the POP3
server is correct.

Note

Main
code

Sub

code

Title

The specified mail server (POP3)
suspends response.

CE

08

Phenomenon

Display

Lamp

Message

Details

The specified mail server
(POP3) suspends
response.
POP3 server time-out
error

Section
Operation
mode
Note

Case 1

Trouble
position/
Cause

Improper connection of
the network cable

Remedy

Check connection of the
network cable.

Note

Case 2

Trouble
position/
Cause
Remedy

An error occurs in the
POP3 server.

Note

Check for any error in the
POP3 server.

Main
code

Sub

code

Title

CIS shading trouble (White
correction)

E6

11

Phenomenon

Display

Lamp
Message

Details

CIS shading trouble
(White correction)
When the power is
turned on or when the
proper gain setup value
is not obtained with SIM
63-2 CIS shading (Retry
number: 256 times):
CIS white reference plate
scan level is abnormal
when the lamp is lighted.

Section

Scanner

Operation
mode

Note

Case 1

Trouble
position/
Cause

Defective installation of
the harness to the CIS
unit
CIS unit abnormality

Remedy

CIS unit harness check

Note

Case 2

Trouble
position/
Cause

Reference white plate
dirt

Remedy

Clean the reference
white plate.

Note

Case 3

Trouble
position/
Cause

CIS lighting trouble

Remedy

Use SIM 5-3 to check the
light quantity of CIS.

Note

Case 4

Trouble
position/
Cause

Scanner PWB
abnormality

Remedy

Scanner PWB check

Note

Main
code

Sub

code

Title

CIS communication trouble

E6

14

Phenomenon

Display

Lamp

Message

Details

CIS communication
trouble
When an error occurs in
an access check to the
CIS-ASIC on turning on
the power or closing the
DSFP cover. (Retry
number: 5 times)
Communication trouble
between the scanner
PWB and the CIS-ASIC.
(Clock synchronization)

Section

Scanner

Operation
mode

Note

«
...
362
363
364
365
366
...
»

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов