Sharp AR-M550N Скачать руководство пользователя страница 349 | Manualshive

Страница: 349 / 460

Sharp AR-M550N Скачать руководство пользователя страница 349

AR-M550/M620/M700 SIMULATION 8 - 91

Operation/Procedure

1) Enter 0 with 10-key.

2) Press [START] key.

The dial signal is outputted.

(Dial pulse make time setting)

1) Enter 1 or 2 with 10-key.

2) Press [START] key.

3) Enter the set value with 10-key.

4) Press [START] key.

When [CUSTOM SETTINGS] key is pressed during execution, the
operation is stopped.

Operation/Procedure

1) Enter the DTMF signal (1 - 9, 0, *, #) to be sent with 10-key.

2) Press [START] key.

The signal is sent in the max. send level.

When [CUSTOM SETTINGS] key is pressed during execution, the
operation is stopped.

66-16

Purpose

Setting/Operation test/Check

Function
(Purpose)

Used to check the dial signal (DTMF) output in the FAX
tone dial mode. (The dial number signal set by SIM 66-
13 is outputted.) The send level can be set to an
optional level. Used to check troubles in dialing and to
check the operation. (Only when FAX is installed)

Section

FAX

Item

Operation

Item

Set range

0

EXECUTE

Execution

1

HIGH

High group level

0 - 15dB

2

HIGH LOW

High group - Low group

0 - 15

SIMULATION 66-15

DIAL TEST(20PPS). SELECT 0-1, AND PRESS START.

0. EXECUTE

1. MAKE TIME

7

; [+9 ms]

SIMULATION 66-15

DIAL TEST(20PPS). SELECT 0-15, AND PRESS START.

[1. MAKE TIME]

1

7

SIMULATION 66-15

DIAL TEST(20PPS). EXECUTING···.

1. MAKE TIME

7

; [+9 ms]

Press [CUSTOM SETTINGS] key.

Press [CUSTOM SETTINGS] key
or press [START] key.

Select 1 and
press [START] key.

Select 0
and press
[START] key.

Select 0 and press [START] key.

Press [CUSTOM SETTINGS] key.

66-17

Purpose

Setting

Function
(Purpose)

Used to check the dial signal (DTMF) output in the FAX
tone dial mode. Send level: Max. Used to check the
operation. (Only when FAX is installed)

Section

FAX

Item

Operation

Press [START] key.

Press [CUSTOM SETTINGS] key.

SIMULATION 66-16

DIAL TEST(DTMF). SELECT 0-2, AND PRESS START.

0. EXECUTE

1. HIGH

7

(dB) 2. HIGH-LOW

7

SIMULATION 66-16

DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.

1. HIGH(dB)

1

7

Press [CUSTOM SETTINGS] key
or press [START] key.

Select 1 or 2, and

press [START] key.

(When 1)

SIMULATION 66-16

DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.

1. HIGH(dB)

7

(When 2)

SIMULATION 66-16

DIAL TEST(DTMF). EXECUTING···.

1. HIGH

7

(dB) 2. HIGH-LOW

7

SIMULATION 66-17

DTMF SIGNAL OUTPUT.(LEVEL MAX) INPUT 0-9, *, #, AND

PRESS START.

1

SIMULATION 66-17

DTMF SIGNAL OUTPUT.(LEVEL MAX) EXECUTING···.

1

«
...
347
348
349
350
351
...
»

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов