Important Safeguards and Warnings
The following description is the correct application method of the device. Read the
manual carefully before use to prevent danger and property loss. Strictly conform to
the manual during application and keep it properly after reading.
Operating Requirement
Install the PoE front-end device indoors.
The device does not support wall mount.
Don’t place and install the device in an area exposed to direct sunlight or near heat
generating device.
Don’t install the device in a humid, dusty or fuliginous area.
Keep its horizontal installation, or install it at stable places, and prevent it from
falling.
Don’t drip or splash liquids onto the device; don’t put on the device anything filled
with liquids, in order to prevent liquids from flowing into the device.
Install the device at well-
ventilated places; don’t block its ventilation opening.
Use the device only within rated input and output range.
Don’t dismantle the device arbitrarily.
Transport, use and store the device within allowed humidity and temperature range.
Power Requirement
Make sure to use the designated battery type. Otherwise there may be explosion
risk.
Make sure to use batteries according to requirements; otherwise, it may result in fire,
explosion or burning risks of batteries!
To replace batteries, only the same type of batteries can be used.
Make sure to dispose the exhausted batteries according to the instructions.
The product shall use electric wires (power wires) recommended by this area, which
shall be used within its rated specification.
Make sure to use standard power adapter matched with this device. Otherwise, the
user shall undertake resulting personnel injuries or device damages.
Use power supply that meets SELV (safety extra low voltage) requirements, and
supply power with rated voltage that conforms to Limited Power Source in
IEC60950-1. For specific power supply requirements, please refer to device labels.
Products with category I structure shall be connected to grid power output socket,
which is equipped with protective grounding.
Appliance coupler is a disconnecting device. During normal use, please keep an
angle that facilitates operation.
Содержание ELITE Network IP Series
