Panasonic LP-GS Series Скачать руководство пользователя страница 63

Страница: 63 / 190

3-4-2 Operation procedure with external control

⿎

Operation example when controlling the laser marker from external control devices such as
PLC

Refer to “3-4-4 Remote mode settings” (P.67).

The device is ready for receiving the marking starting signal (trigger).

Turn ON key switch of laser marker controller

Marking

Control by serial communication

commands

I/O control

OPEN shutter

Remote mode ON

Select file

Confirm READY OUT is ON.

Trigger Input ON

Laser pumping ON

Control by using I/O or
communication commands

ンㄆㄇㄆㄓㄆㄏ㄄ㄆ

• It is available to the external control combining I/O, and serial communication commands.
• You need to configure the system settings on the I/O communication in advance before using external control. Refer to

“3-4-3 Settings before external control” (P.64).

• For details on the operation procedure when you link an image checker or a code reader, refer to “6 Link Control with

External Devices” (P.116).

ME-LPGS-SM-8

Содержание LP-GS Series































































































































































































Результаты поиска

Содержание LP-GS Series

Отзывы:

Похожие инструкции для LP-GS Series

Бренды по названию

Популярные бренды

Panasonic LP-GS Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание LP-GS Series

Отзывы:

Похожие инструкции для LP-GS Series

Бренды по названию

Популярные бренды