Panasonic LP-GS Series Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 190

background image

110

⿎

Connecting to external control devices

• To connect the laser marker to the PC for control, use a commercially available RS-232C straight cable (laser marker

side: 9pin male).

• In case of connecting to PLC, a type of the cable (straight or cross) differs depending on a manufacturer or a model.

Please follow the PLC manual.

• To connect RS-232C terminal without using a commercially available RS-232C cable, connect only 3 signals of RxD,

TxD and GND and do not use other signals on the laser marker side.

• You may need a signal line connection (loop back line) other than RxD (RD), TxD (SD) or GND on the external control

device side depending on the specifications of the external control device. Read the instruction manual of the external
control device and connect it to the laser marker appropriately.

Connection example

RxD

TxD

GND

DCD

DTR

DSR

RTS

CTS

2

3

5

1

4

6

7

8

TxD

RxD

GND

2

3

5

RS-232C port

(Laser marker)

External control devise

Straight cable

Signal

Signal

*

Terminal No.

Terminal No.

* The loop back wiring on the external control device side shown in the above figure is just an example. The wiring method

varies depending on the specifications of each external control device. Read the instruction manual of the external
control device and connect it to the laser marker appropriately.

ME-LPGS-SM-8

«
...
108
109
110
111
112
...
»

Содержание LP-GS Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LP-GS Series

Бренд: DARAY Страницы: 28

Бренд: MacDon Страницы: 88

Бренд: Jiffy Страницы: 15

Бренд: NEC Страницы: 54

Бренд: TC Electronic Страницы: 2

Бренд: Bahco Страницы: 131

Бренд: Bahco Страницы: 126

Бренд: Olsen Страницы: 4

Dominator Series

Бренд: Falcon Страницы: 31

Бренд: Fakir Страницы: 22

Бренд: IBEX Страницы: 4

Бренд: IDEAL Networks Страницы: 10

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

Бренд: V-TAC Страницы: 13

Бренд: Kanlux Страницы: 4

NESLAB System IV

Бренд: Thermo Scientific Страницы: 22

Бренд: QTX Light Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды