Panasonic LP-GS Series Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 190

background image

115

5-4 Checking the communication commands

Check the communication commands transmitted and received by the laser marker using the command history function in
the PC configuration software “Laser Marker NAVI smart”.
The command history is displayed with the following procedures.

1.

Connect Laser Marker NAVI smart and the laser marker online.

2.

Click the screen selection menu and select “Maintenance”.

3.

Select “Command history” tab. Up to 100 command messages received or sent by the laser
marker are shown in the list.

ンㄆㄇㄆㄓㄆㄏ㄄ㄆ

• In the command history the transmitted and received data via RS-232C and Ethernet ports are recorded.
• When a code reader is connected to the RS-232C port of the laser marker, the transmitted and received data with the

code reader is not recorded in the command history.

ME-LPGS-SM-8

«
...
113
114
115
116
117
...
»

Содержание LP-GS Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LP-GS Series

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: ZOLL Страницы: 84

Бренд: Kaivac Страницы: 29

Бренд: MacDon Страницы: 65

Бренд: parr Страницы: 20

Бренд: Landoll Страницы: 71

Бренд: York Fitness Страницы: 4

Бренд: W&H Страницы: 23

Бренд: Bartscher Страницы: 24

Бренд: Above All Страницы: 4

Бренд: Baoding Longer Precision Pump Страницы: 6

Бренд: MacDon Страницы: 46

Бренд: MacDon Страницы: 82

Бренд: Mac Medical Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды