Panasonic LP-GS Series Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 190

background image

149

3.

Loosen the screws (4 screws for 1 fan), and
remove the fan guard and the fan itself from
the controller.

4.

Remove dust and dirt adhered onto the fan by air-blowing.

ワㄐㄕㄊ㄄ㄆ

• Do not rinse the fan. This may cause failure of the electronic parts inside.

5.

Install the fan guard against the direction of arrow on the
side of the fan indicating the air flow, as shown in the figure
on the right (exhaust direction).

ワㄐㄕㄊ㄄ㄆ

• Install the controller fan in the direction so that the air flow matches the

exhaust direction.
Fan installed in the wrong way causes the flow to go in the wrong way,
which may failure of the product.

6.

Install the fan so that the fan cable will be routed
in the place as shown in the figure on the right.
Fasten the screws (M4, depth 35 mm) (4 screws
for 1 fan) from the top of the fan guard to secure
the fan to the controller.

Tightening torque: 1.0 N·m

ワㄐㄕㄊ㄄ㄆ

• Be careful not to let the cable get caught while installing.

7.

Connect the connector for the fan. (One
connector for one fan)

8.

If you replaced the fans to new one, reset the
runtime information in Laser Marker NAVI smart.

Open “Runtime data” in “Maintenance” view and click “Reset”
of the controller fan operating time.

Fan guard

Fan

Screws

Fan guard

Airflow direction

Fan

Screws

Connector

Fan

ME-LPGS-SM-8

«
...
147
148
149
150
151
...
»

Содержание LP-GS Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LP-GS Series

Бренд: 3M Страницы: 2

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Бренд: Kawai Страницы: 10

Бренд: Eaton Страницы: 21

Бренд: Eaton Страницы: 70

Бренд: NANO Страницы: 4

Бренд: Madrigal Страницы: 5

Бренд: MacDon Страницы: 504

ThermoTweez Handpiece TT-65

Бренд: Pace Страницы: 14

Бренд: Safavieh Страницы: 2

Бренд: Vendlet Страницы: 2

Бренд: M-Audio Страницы: 48

Бренд: M-Audio Страницы: 19

Бренд: M-Audio Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды