Panasonic LP-GS Series Скачать руководство пользователя страница 60

Страница: 60 / 190

Check the box next to “Clear the password” on the
screen displayed, and then, click “OK”.

Start Laser Marker NAVI smart and establish an online connection with the laser marker of which
password setting you want to delete.

This deletes the password, and the password lock in switching the screens is released.

Exit from the Laser Marker NAVI smart.

Execute ClearPassword.exe again. If “Clear the
password” remains enabled, then, click “OK”.

ワㄐㄕㄊ㄄ㄆ

• If “Clear the password” remains enabled, the password will

be deleted when connected to online even without executing
ClearPassword.exe. Make sure to uncheck the box next to “Clear
the password”.

To reconfigure the password, start Laser Marker NAVI
smart and select “System settings” on the screen selection
menu. Display the “Access premissions” panel and enter
the password for screen switching.

ンㄆㄇㄆㄓㄆㄏ㄄ㄆ

• For details on the system settings, please refer to the Laser Marker NAVI

smart Operation Manual.

Click “Set” on the lower right corner of the screen.

The password setting will become enabled.

ME-LPGS-SM-8

Содержание LP-GS Series































































































































































































Результаты поиска

Содержание LP-GS Series

Отзывы:

Похожие инструкции для LP-GS Series

Бренды по названию

Популярные бренды

Panasonic LP-GS Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание LP-GS Series

Отзывы:

Похожие инструкции для LP-GS Series

Бренды по названию

Популярные бренды