manualshive.com logo in svg

Mitsubishi MELFA CR1D, Инструкция по эксплуатации

"Кроботизированная линейка Mitsubishi MELFA CR1D - надежный помощник в автоматизации производства. Управляйте им с помощью подробной Инструкции, которую вы можете бесплатно скачать с manualshive.com. Этот мануал поможет вам максимально эффективно использовать все функции этого продукта."

Поделиться
Скачать
background image

4-177   

Detailed explanation of command words

4MELFA-BASIC IV

ColLvl (Col Level)

[Function]

Set the detection level of the impact detection function in automatic operation.
The impact detection function can only be used in certain models (Refer to "[Available robot type]".). 

[Format] 

[Terminology]

<J1 to J6 axis>

Specify the detection level in a range between 1 and 500%. 
If omitted, the previously set value is retained.
This instruction is invalid for the J7 and J8 axes.
The initial value is the setting value of the ColLvl parameter.

[Reference Program]

1 ColLvl 80,80,80,80,80,80,,

'Specify the allowable level for impact detection.

2 ColChk On

'Enable the impact detection function.

3 Mov P1
4 ColLvl ,50,50,,,,,

'Change the allowable level of the J2 and J3 axes for impact detection.

5 Mov P2
6 Dly 0.2

'After arriving at P2, disable impact detection.

7 ColChk Off

'Disable the impact detection function.

8 Mov P3

[Explanation]

(1) Set the allowable level of each axis for the impact detection function during program operation.
(2) This instruction affects the impact detection function in automatic operations (including step feed and 

step jump operations). If a program is not running (pause status or during jog operation), the setting level 
of the ColLvlJG parameter is used.

(3) Normally, the setting value of the allowable level immediately after power ON is the setting value of the 

ColLvl parameter.

(4) "All axes 100%" is set as the initial value of the ColLvl parameter.
(5) If this value is increased, the detection level (sensitivity) lowers; if this value is lowered, the detection 

level increases. 

(6) If the detection level is increased, the probability of erroneous detection becomes high. Adjust the level 

such that it does not become too high. Depending on the posture and operation speed, erroneous 
detection may also occur with the initial value. In this case, the detection level should be lowered. 

(7) The impact detection function may not work properly if the hand weight (HNDDATn parameter) and 

workpiece weight (WRKDATn parameter) are not set correctly. Be sure to set these parameters correctly 
before using.

(8) When the continuity function is enabled, the previously set value is restored at next power ON even if the 

power is turned OFF.

(9) The allowable level is reset to the setting value of the ColLvl parameter when a program reset or an End 

instruction is executed.

(10) Even if an attempt is made to execute this instruction on robots that cannot use the impact detection 

function, the instruction is ignored and thus no error occurs.

(11) The impact detection function is not valid for the J7 and J8 axes.
(12) The correct setting value may vary even among robots of the same type due to individual differences of 

units. Check the operation with each robot.

[Related instructions and variables]

ColChk (Col Check), M_ColSts, J_ColMxl, P_ColDir

[Related parameter]

COL,COLLVL, HNDDATn, WRKDATn

[Available robot type] 

ColLvl[] [<J1 axis>],[<J2 axis>],[<J3 axis>],[<J4 axis>],[<J5 axis>],[<J6 axis>],,

RV-6SD/6SDL/12SD/12SDL series

Содержание MELFA CR1D











































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELFA CR1D

Vacon 20 Quick Manual preview
20
Бренд: Vacon Страницы: 62
FAAC 740 D Manual preview
740 D
Бренд: FAAC Страницы: 14
IBM 3708 End-User Reference preview
3708
Бренд: IBM Страницы: 144
UNITED C5 Series Installation & Service Manual preview
C5 Series
Бренд: UNITED Страницы: 22
Hafele DT 100 Operating Instructions Manual preview
DT 100
Бренд: Hafele Страницы: 82
Oldham MX15 Installation And Operating Manual preview
MX15
Бренд: Oldham Страницы: 32
H3C PSR3000-54A Manual preview
PSR3000-54A
Бренд: H3C Страницы: 14
Icom IC-706MKII Manual preview
IC-706MKII
Бренд: Icom Страницы: 30
ICM Controls ICM330 Manual preview
ICM330
Бренд: ICM Controls Страницы: 2
ICM Controls ICM2909 Manual preview
ICM2909
Бренд: ICM Controls Страницы: 2
ray Super Remote Setting Up preview
Super Remote
Бренд: ray Страницы: 11
Samson FOUNDATION 3730-5 Mounting And Operating Instructions preview
FOUNDATION 3730-5
Бренд: Samson Страницы: 132
Samson 3767 Mounting And Operating Instructions preview
3767
Бренд: Samson Страницы: 68
Samson 3730-2 Mounting And Operating Instructions preview
3730-2
Бренд: Samson Страницы: 128
Samson 3725 series Mounting And Operating Instructions preview
3725 series
Бренд: Samson Страницы: 68
X-POWER MULTI 1 Instruction And Installation Manual preview
MULTI 1
Бренд: X-POWER Страницы: 24
Samson TROVIS 3730-1 Mounting And Operating Instructions preview
TROVIS 3730-1
Бренд: Samson Страницы: 80
Haehne DCX Quick Start Manual preview
DCX
Бренд: Haehne Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды