Mitsubishi MELFA CR1D Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 458

background image

3Explanation of operation methods

Operation of the origin and the brake screen

3-76

3.15 Operation of the origin and the brake screen

(1) O

origin

If the origin position has been lost or deviated when the parameters are lost or due to robot interference, etc.,

the robot origin must be set again using this function.

Refer to the separate manual: "Robot arm setup & maintenance" for details on the operation.

(2) Brake

In the state of servo off, it is the function to release the brake of the servo motor. Refer to the

Turning the servo ON/OFF" for servo off operation.
Use it, if it moves the robot arm directly by hand.

Due to the robot configuration, when the brakes are released, the robot arm will drop
with its own weight depending on the released axis.
Always assign an operator other than the T/B operator to prevent the arm from
dropping. This operation must be carried out with the T/B operator giving signals.
Refer to

and accurately designate the axis for which the brakes are to be

released.

Table 3-6:The brake release axis unit classified by type

Note

）　 " ■ "mark means that brake release with the independent axis is possible.

The operation method is shown in the following. Perform this operation, in the condition that the enabling switch

(3 position switch) is pushed lightly.

1) Press the [4] key in the monitor menu screen, and display the origin/brake screen.

2) Press the [2] key in the origin/break screen, and display the break release screen.

Type

　　　　　　 Axis
１　２　３　４　５　６　７　８

Remarks

RV-SQ/SD series

■ 　 ■ 　 ■ 　 ■ 　 ■ 　 ■

CAUTION

<MENU>　　　

1.FILE/EDIT 2.RUN
3.PARAM.

4.ORIGIN/BRK

5.SET/INIT.

CLOSE

　 123

<ORIGIN/BRAKE>　　　

1.ORIGIN 2.BRAKE

CLOSE

　 123

<BRAKE>

J1:(

0

)J2:( 0 )J3:( 0 )

J4:( 0 )J5:( 0 )J6:( 0 )
J7:( 0 )J8:( 0 )

CLOSE

123

REL.

<ORIGIN/BRAKE>　　　

1.ORIGIN 2.BRAKE

CLOSE

　 123

«
...
87
88
89
90
91
...
»

Содержание MELFA CR1D











































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELFA CR1D

Бренд: Gantner Страницы: 56

Бренд: ABB Страницы: 63

Бренд: JDS Uniphase Страницы: 27

Бренд: Danfoss Страницы: 20

Бренд: OEG Страницы: 168

Бренд: Gardigo Страницы: 8

Бренд: Gardigo Страницы: 19

Бренд: Febco Страницы: 12

Бренд: HANYOUNG NUX Страницы: 74

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 2

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 36

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

Бренд: National Instruments Страницы: 8

Бренд: UNICORECOMM Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды