Mitsubishi MELFA CR1D Скачать руководство пользователя страница 242 | Manualshive

Страница: 242 / 458

background image

4-229

Detailed explanation of command words

4MELFA-BASIC IV

Oadl (Optimal Acceleration)

[Function]

Automatically sets the optimum acceleration/deceleration according to the robot hand's load state (Optimum
acceleration/deceleration control).
By employing this function, it becomes possible to shorten the robot's motion time (tact).
The acceleration/deceleration speed during optimum acceleration/deceleration can be calculated using the
following equation:

Acceleration/deceleration speed (sec) = Optimum acceleration/deceleration speed (sec) x Accel instruction
(%) x M_SetAdl (%)

* The optimum acceleration/deceleration speed is the optimum acceleration/deceleration speed calculated
when an Oadl instruction is used.

[Format]

[Terminology]

<On / Off>

ON : Start the optimum acceleration/deceleration speed.
OFF : End the optimum acceleration/deceleration speed.

[Reference Program]

1 Oadl On
2 Mov P1

' Move with maximum load.

3 LoadSet 1ÅC1

' Set hand 1 and workpiece 1.

4 Mov P2

' Move with hand 1 + workpiece 1 load.

5 HOpen 1

'

6 Mov P3

' Move with hand 1 load.

7 HClose 1

'

8 Mov P4

' Move with hand 1 + workpiece 1 load.

9 Oadl Off

*When parameter HNDHOLD1 is set to 0, 1

[Explanation]

(1) The robot moves with the optimum acceleration/deceleration according to the hand conditions and work-

piece conditions designated with the LoadSet command.

(2) The workpiece grasp/not grasp for when the hand is opened or closed is set with parameter HNDHOLD

1 to 8.

(3) Initial setting of Oadl can be changed by the ACCMODE parameter. (Refer to

Page 351, "Table 5-2: List

Signal parameter"

)

(4) Once Oadl is On, it is valid until Oadl Off is executed or until the program End is executed.
(5) Depending on the conditions of the hand and/or workpiece, the motion time may become longer than

usual.

(6) It is possible to perform the optimum acceleration/deceleration operation by using the LoadSet and Oadl

instructions, and by setting the HNDDAT1(0) through 8 and WRKDAT1(0) through 8 parameters to
appropriate values. (Refer to

Page 377, "5.16 Hand and Workpiece Conditions (optimum acceleration/

deceleration settings)"

)

(7) The value of the acceleration/deceleration speed distribution rate in units of axes are predetermined by

the JADL parameter. This value varies with models in the S series. Refer to the JADL parameter.

Oadl[]<On / Off>

«
...
240
241
242
243
244
...
»

Содержание MELFA CR1D











































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELFA CR1D

FEPL-02 Ethernet POWERLINK

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 2

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 16

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

Бренд: IBM Страницы: 12

Бренд: K&K Страницы: 10

Бренд: Manfrotto Страницы: 16

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: Barco Страницы: 6

Бренд: Kasco Страницы: 3

Бренд: C Prox Ltd Страницы: 5

Бренд: IDS Страницы: 2

Бренд: ZKTeco Страницы: 13

Бренд: UniPi Technology Страницы: 4

Бренд: Parker Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды