GigaDevice Semiconductor GD32W515 Series Скачать руководство пользователя страница 330

Страница: 330 / 1044

GD32W51x User Manual

330

data in the FIFO for a peripheral transfer, DMA starts a peripheral transfers to fetch the

FIFO data and write to the peripheral.



Memory-to-memory mode: Only the multi-data mode is supported. When the channel is

enabled, DMA starts several peripheral transfers to fill up the FIFO. During the

transmission, the peripheral transfer is initiated once when there is enough space for it

in the FIFO.

12.4.9.

Transfer finish

The DMA transfer is finished automatically and the FTFIFx bit in the DMA_INTF0 or

DMA_INTF1 register is set when one of the following situations occurs:



Transfer completion



Software clear



Error detection

Transfer completion

When enabled, the DMA begins to transfer data between peripheral and memory. After the

pre-programmed number of data items has been transferred successfully, the DMA transfer

is completed and the CHEN bit is automatically cleared in the DMA_CHxCTL register.



Peripheral-to-memory mode: If DMA is the transfer flow controller, when the CNT bits

reach to zero and the contents of the FIFO have been entirely transferred into the

memory, an end of transfer is generated. If peripheral is the transfer flow controller, the

DMA transfer is completed when the last peripheral request has been responded and

the contents of the FIFO have been entirely transferred into the memory.



Memory-to-peripheral mode: If DMA is the transfer flow controller, when the CNT bits in

the DMA_CHxCNT register reach to zero, an end of transfer is achieved. If peripheral is

the transfer flow controller, the DMA transfer is completed when the last peripheral

request has been responded.



Memory-to-memory: only DMA can be the transfer flow controller. When the CNT bits

reach to zero and the contents of the FIFO have been entirely transferred into the

memory, an end of transfer is generated.

Software clear

The DMA transfer can be stopped by clearing the CHEN bit in the DMA_CHxCTL register by

software. After the software cleared operation, the CHEN bit is still read as 1 to indicate that

there are memory or peripheral transfers still active or the remaining data in the FIFO need

to be transferred.



Peripheral-to-memory: After the software cleared operation, the peripheral transfer is

stopped when the current single or burst transfer is completed. To ensure that the data

had been read from peripheral can be entirely transferred into the memory, the memory

transfer continues to be active until the FIFO is empty. If the remaining byte number in

Содержание GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32W515 Series

Отзывы:

Похожие инструкции для GD32W515 Series

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32W515 Series, Руководство пользователя

Результаты поиска

Содержание GD32W515 Series

Отзывы:

Похожие инструкции для GD32W515 Series

Бренды по названию

Популярные бренды