S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
20-6
Cisco MDS 9000 Family Troubleshooting Guide, Release 3.x
OL-9285-05
Chapter 20 Troubleshooting IP Storage Services
IP Issues
64 bytes from 11.18.185.121: icmp_seq=1 ttl=128 time=0.1 ms
64 bytes from 11.18.185.121: icmp_seq=2 ttl=128 time=0.2 ms
64 bytes from 11.18.185.121: icmp_seq=3 ttl=128 time=0.2 ms
64 bytes from 11.18.185.121: icmp_seq=4 ttl=128 time=0.1 ms
64 bytes from 11.18.185.121: icmp_seq=5 ttl=128 time=0.1 ms
--- 11.18.185.121 ping statistics ---
6 packets transmitted, 6 packets received, 0% packet loss
round-trip min/avg/max = 0.1/0.1/0.3 ms
Step 2
If the ping fails, use the
traceroute
or the
traceroute ipv6
command to determine where connectivity
is failing.
switch#
traceroute
11.18.185.121
traceroute to 11.18.185.121 (11.18.185.121), 30 hops max, 38 byte packets
1 11.18.189.129 (11.18.189.129) 0.413 ms 0.257 ms 0.249 ms
2 11.18.0.33 (11.18.0.33) 0.296 ms 0.260 ms 0.258 ms
3 11.81.254.69 (11.81.254.69) 0.300 ms 0.273 ms 0.277 ms
4 * * *
5 * * *
Step 3
Use
show ip route
or the
show ipv6 route
command to
verify the static route to the remote device.
switch #
show ip route
Codes: C - connected, S - static
Default gateway is 11.18.185.97
C 11.18.185.96/27 is directly connected, mgmt0
C 11.18.189.128/26 is directly connected, gigabitethernet4/7
Step 4
Use the
clear ips arp
or
clear ipv6 neighbor
command to clear the Address Resolution Protocol (ARP)
or neighbor cache to verify that the activity you are viewing is the most current.
switch#
clear ips arp interface gigabitethernet 4/7
arp clear successful
Step 5
Use the
show ips arp
or the
show ips ipv6 neighbors
command to verify the hardware address for the
remote device.
switch#
show ips arp interface gigabitethernet 4/7
Protocol Address Age (min) Hardware Addr Type Interface
Internet 172.18.185.97 0 00:d0:01:3b:38:0a ARPA GigabitEthernet4/7
Internet 172.18.189.156 0 00:08:02:b3:45:1b ARPA GigabitEthernet4/7
Step 6
Use the
show interface
command to verify that the Gigabit Ethernet interface is up.
GigabitEthernet4/7
is up
Hardware is GigabitEthernet, address is 0005.3000.9f58
Internet address is 172.18.189.137/26
MTU 1500 bytes, BW 1000000 Kbit
Port mode is IPS
Speed is 1 Gbps
Beacon is turned off
5 minutes input rate 688 bits/sec, 86 bytes/sec, 0 frames/sec
5 minutes output rate 312 bits/sec, 39 bytes/sec, 0 frames/sec
156643 packets input, 16859832 bytes
0 multicast frames, 0 compressed
0 input errors, 0 frame, 0 overrun 0 fifo
144401 packets output, 7805631 bytes, 0 underruns
0 output errors, 0 collisions, 0 fifo
0 carrier errors
