YOKOGAWA ScopeCorder DL950 User Manual Download Page 281

Page: 281 / 316

20-7

IM DL950-02EN

20.3 Accessing the Instrument from a PC (FTP

Server)

This section explains the following settings for accessing the instrument from a PC on a network:

Items Common to Scope Mode and Recorder Mode

•  User name
•  Password
•  Timeout
•  Starting an FTP client

► “FTP Server (FTP/Web Server)” in the Features Guide

UTILITY Network Menu

On the waveform screen’s MENU, tap

OTHERS

UTILITY

, or press

UTILITY

Tap

Network

, or press the soft key. The following screen appears.

Select Network.

See “Configuring the FTP Server.”

(For information on the Web server, see

section 20.4.)

Configure the TCP/IP settings

► sec. 20.2

Configure mail settings. ► sec. 20.6

Configure network printing. ► sec. 20.8

Configure the network drive. ► sec. 20.5

Configure SNTP. ► sec. 20.7

Configure the TCP/IP settings

► sec. 20.2 (/C60 option)

Configuring the FTP Server (FTP/Web Server)

Tap

FTP/Web Server

, or press the soft key. The following screen appears.

Set the user name (up to 15 characters).

Set the password (up to 15 characters).

Set the timeout (30 to 3600).

Applies the settings

Selects 1G or 10G (displayed for the /C60 option)

Note

If you set the user name to “anonymous,” you can connect to the instrument without entering a password.

Starting an FTP Client

Start an FTP client on a PC. Enter the user name and password that you have set on the
instrument’s FTP/Web Server screen shown above, and connect to the instrument.

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL950, User Manual

Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands