manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 256

19-10

IM DL950-02EN

Setting the Save Destination (File List)

3.

 Tap 

File List

, or press the soft key. The following screen appears.

  

Save destination drive (storage device) or folder

Use the jog shuttle or the up and down arrow keys (▲▼) 

to move the cursor, and press SET to make your selection.

Operation 

menu

For more information on file operations, see section 19.10.

Assigning File Names (File Name)

3.

 Tap 

File Name

, or press the soft key. The following screen appears.

  

Set the auto naming method (OFF, Numbering, Date).

Set the file name.

Set comments.

Note

•  Auto naming, file name, and comment settings are shared with SSD recording. The settings that you 

specify here will be applied to the SSD recording settings.

•  When dual capture is on, “_HS” is appended to the file names of high-speed sampling and “_LS” to the 

file names of low-speed sampling.

Setting Auto Naming (Auto Naming)

OFF:       The auto naming feature is disabled. The file name specified using the File Name 

setting is used. If there is a file with the same name in the save destination folder, 
you cannot save the data.

Numbering:  A 4-digit serial number (0000 to 9999) is automatically appended to the common 

name (up to 32 characters) specified with the File Name setting.

19.4  Saving Waveform Data

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands