YOKOGAWA ScopeCorder DL950 User Manual Download Page 278

Page: 278 / 316

20-4

IM DL950-02EN

To Connect to a PC through a Hub or Router

Turn off the instrument and the PC.

Connect the connector on one end of a UTP (or STP) cable to the ETHERNET 1000BASE-T

port on the side panel or the connector on one end of an STP+ cable to the 10GBASE-R port
on the side panel.

Connect the other end of the UTP (or STP) or SFP+ cable to a hub or router.

Connect the PC to the hub or router in the same way.

Turn on the instrument.

Hub or router that supports 1000BASE-T or 10GBASE-R

UTP or STP cable

(straight cable)

SFP+ cable when using 10G Ethernet (/C60 option)

(Straight cable)

DL950

Note

• Use a hub or router that conforms to the transfer speed of your network.

• To connect a PC to the instrument through a hub or router, the PC must be equipped with an auto

1000BASE-T/100BASE-TX/10BASE-T switching or 10GBASE-R network card.

• Do not connect the instrument to a PC directly. Direct communication without a hub or router is not

guaranteed to work.

• If you specify a fixed IP address or network drive, be sure to use the instrument in an environment where

it can be accessed. If it cannot be accessed, you may not be able to operate the instrument for the

specified timeout period.

20.1 Connecting the Instrument to a Network

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL950, User Manual

Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands