YOKOGAWA ScopeCorder DL950 User Manual Download Page 192

Page: 192 / 316

13-4

IM DL950-02EN

13.2 Setting the Math Waveform Scaling

This section explains the following settings for displaying computed waveforms:

Items Common to Scope Mode and Recorder Mode

• Vertical scale

► “Scaling Mode (Scaling)” in the Features Guide

Math Menu

On the waveform screen’s MENU, tap

ANALYSIS > MATH

, or press

SHIFT+FFT (MATH)

. The

Math menu appears.

Set the math mode to ON.

Set the expression. ► sec. 13.1

Set the math waveform to set scaling (1 to 8).

Set the scaling mode (Auto, Manual).

Set averaging. ► sec. 13.3

(For user-defined math function, /G02 option)

Set the upper and lower limits.

(When the linear scaling mode is Manual)

Set the math range. ► sec. 13.1

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL950, User Manual

Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Brands by name

Popular brands