manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 98

4-10

IM DL950-02EN

4.7  Triggering on a Logic Trigger (Simple)

This section explains the following settings for triggering on the edges of a logic-signal trigger 
source:

Applicable in Scope Mode

•  Trigger source
•  Source bit
•  Trigger slope

► “Simple Trigger (Simple)” and “Trigger Source (Source)” in the Features Guide

Trigger Menu

1.

  On the waveform screen’s 

MENU

, tap 

TRIGGER 

> 

MENU

, or press 

TRIG.MENU

. A trigger 

menu appears.

  

Set the trigger position, trigger delay, and hold-off 

► sec. 4.2

Select Simple.

See “Setting the Trigger Source.”

Set the trigger slope (    ,      ).

Set the trigger mode. ► sec. 4.1

Setting the Trigger Source (Source)

2.

  Press the 

Source

 soft key. The following menu appears.

  

Set the source channel

(logic input module)

Set the source bit.

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands