YOKOGAWA ScopeCorder DL950 User Manual Download Page 158

Page: 158 / 316

9-6

IM DL950-02EN

Searching by Automatically Measured Parameter (Search Setup)

Tap

Search Mode

, or press the soft key. On the menu that appears, Search Mode to

Parameter

Tap

Search Setup

, or press the soft key. The following screen appears.

Register the search parameter (Pram1-Param4).

Set the search condition (OFF, IN, OUT).

See “Sitting the Source Waveform and Parameters.”

Set the upper and lower search condition limits.

Set the search logic (AND, OR).

(For Param1 to Pram4)

Measurement time period of the parameter (left edge –

Time Range1; right edge – Time Range2).

(For Param1 to Pram4)

For all items other than Logic and Time Range1, 2, set for each Param.

Sitting the Source Waveform and Parameters (Source)

Press the

Source

soft key. The following menu appears.

Select the source waveform (CH1, CH16).

Set the waveform parameter type. ► sec 11.1

Executing a History Waveform Search

After you set all the search conditions, close the menu to return to the HISTORY menu.

Tap

Execute

, or press the soft key. The instrument searches for the search conditions.

The soft key changes to Abort.

To abort a search, tap

Abort

, or press the soft key.

9.2 Searching History Waveforms

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL950, User Manual

Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Brands by name

Popular brands