manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 148

8-4

IM DL950-02EN

Configuring the Search Result Display Window (Zoom Window) 

(Display Result) (Scope mode)

Set which zoom window, Z1 or Z2, to display the found waveform in. You can configure zoom 
windows Z1 and Z2 when they are displayed. If both Z1 and Z2 are not displayed, Z1 will be 
displayed when you press 

SHIFT+ZOOM

 (SEARCH) to display the SEARCH menu.

Executing a Search (Execute)

4.

 Tap 

Execute

, or press the soft key. The instrument executes the search.

  

Executes the search

This appears when a 

point that matches the 

specified search 

conditions is found.

Detected point 

Executing and Aborting a Search

After setting the search conditions, tap 

Execute

, or press the soft key. The search is executed, and 

the soft key changes to Abort. If the instrument finds points that match the search conditions (detected 
points), it shows numbers (0, 1, 2, etc.) from the left of the waveform display in the order that the 
points were detected.
To abort a search, tap 

Abort

, or press the soft key.

Setting the Detected Point Numbers

You can set the detected point number and display the waveform with the detected point in the 
center of the zoom window.

8.1  Searching for Edges

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands