YOKOGAWA ScopeCorder DL950 User Manual Download Page 58

Page: 58 / 316

2-42

IM DL950-02EN

2.10 Configuring the Monitoring of LIN Bus Signals

(/VCE option)

This section explains the following settings for monitoring LIN bus signals.

Items Common to Scope Mode and Recorder Mode

• Turning waveform input or and off
• LIN frame reading settings (all sub channel settings, factor and offset settings of all sub channels,

frame settings, port settings, definition file loading)

•  Individual sub channel scales
•  Display group
•  Scaling of all sub channels
•  Sample rate and sample interval settings

► “LIN Bus Signal Monitoring (/VCE option)” in the Features Guide

Channel Setup Menu

On the waveform screen’s

MENU

, tap

VERTICAL

, or press

. A channel setup menu

appears.

(You can also tap the channel information display area at the top of the screen to display the
channel setup menu.)

Tap a channel you want to configure, or select it using the jog dial or up and down arrow keys.

Turns the waveform input

on or off

Displays the second

page of the menu

See “Setting the Scale and

Display Groups.”

See “Configuring LIN Frame

Reading Settings.”

Channel setup menu (1/2)

Set the scaling of all sub channels

(All SubChannel Auto,

All SubChannel Default)

Channel setup menu (2/2)

Displays the first page of the menu

Set the sample rate.

(Scope mode)

Set the sample interval.

(Recorder mode)

► sec. 2.1

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL950, User Manual

Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands