manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 276

20-2

IM DL950-02EN

20.1  Connecting the Instrument to a Network

This section explains how to connect the instrument to a network.

Connecting to the Ethernet Port (1000BASE-T/100BASE-

TX/10BASE-T)

Connect an Ethernet cable to the 1000BASE-T port on the side panel of this instrument.
Connector type:  RJ-45 connector

Ethernet port

(1000BASE-T/100BASE-TX/10BASE-T)

RJ-45 modular jack

Items Required to Connect the Instrument to a Network

Cable

Use one of the following types of network cable that conforms to the transfer speed of your 
network.
•  A UTP (Unshielded Twisted-Pair) cable
•  An STP (Shielded Twisted-Pair) cable

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands