manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 93

4-5

IM DL950-02EN

4.3  Triggering on an Edge Trigger (Simple) in 

Scope Mode

This section explains the settings for triggering on the edges of an analog-signal trigger source in 
Scope mode: To use a logic signal for the trigger source, see section 4.7.

Applicable in Scope Mode

•  Trigger source
•  Trigger slope
•  Trigger level
•  Trigger hysteresis

► “Simple Trigger (Simple),” “Trigger Source (Source),”

 

“Trigger Slope (Slope),” “Trigger Level (Level),” and

 

“Trigger Hysteresis (Hysteresis)” in the Features Guide

Trigger Menu

1.

  On the waveform screen’s 

MENU

, tap 

TRIGGER 

> 

MENU

, or press 

TRIG.MENU

. A trigger 

menu appears.

  

Set the trigger position, trigger delay, and hold-off 

► sec. 4.2

Select Simple.

See “Setting the Trigger Source.”

Set the trigger slope (   ,      ,        ).

Set the trigger level.

Set the trigger hysteresis (      ,         ,         ).

Set the trigger mode. ► sec. 4.1

Note

If linear scaling is applied to the trigger source, set the trigger level using a linearly scaled value.

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands