manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 116

4-28

IM DL950-02EN

4.17  Triggering on an OR or AND Trigger in 

Recorder Mode

This section explains the following settings for triggering on an OR or AND trigger in Recorder 
mode:

Applicable in Recorder Mode

•  Trigger source
•  Edge detection condition (OR trigger)
•  Achievement condition (AND trigger)
•  Trigger conditions
•  Pre-trigger

►

 “Pre-Trigger (Pre Trigger),” “OR Trigger (Enhanced),” and 

 

“AND Trigger (Enhanced)” in the Features Guide

Trigger Menu

1.

  On the waveform screen’s 

MENU

, tap 

TRIGGER 

> 

MENU

, or press 

TRIG.MENU

. A trigger 

menu appears.

  

Set the trigger type to OR or AND.

See “Setting the State and 

Trigger Conditions.”

Set the pre-trigger.

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands