YOKOGAWA ScopeCorder DL950 User Manual Download Page 200 | Manualshive

Page: 200 / 316

background image

14-3

IM DL950-02EN

Setting the Judgment Conditions (Judgement Setup)

2.

Tap

Judgement Setup

, or press the soft key. The following screen appears.

Set the judgment criterion (X, IN, OUT).

Select the source waveform (CH1 to CH16, Math1 to Math8, FFT1 to FFT8).

Set the zone number (Zone1-Zone6).

Set the determination logic (AND, OR).
Set the action condition (Always, Fail, Success).
Set the sequence (Single, Continue).

Set the number of waveforms to acquire.

Turns external start on or off

Scroll bar

Scroll to display reference conditions that do not fit in

the screen.

Determination Logic (Logic)

AND: The specified action is executed when all the specified judgment conditions are met.
OR: The specified action is executed when any of the specified judgment conditions is met.

Action Condition (Act Condition)

Always: The specified actions is always executed.
Fail: The specified action is executed when the GO conditions are not met.
Success: The specified actions is executed when the GO conditions are met.

Sequence (Sequence)

Single: The specified action is executed once.
Continue: The specified action is executed repeatedly. The specified action is executed until

the number of acquisitions specified by ACQ Count is reached. If ACQ Count is
set to Infinite, the set actions are executed until waveform acquisition is stopped.

14.1 Performing GO/NO-GO Determination with Waveform Zones

«
...
198
199
200
201
202
...
»

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Related manuals for ScopeCorder DL950

Brand: jenway Pages: 18

Brand: Maico Pages: 27

Brand: Magnescale Pages: 14

Professional Plus

Brand: YSI Pages: 28

Brand: Magnescale Pages: 8

Brand: Schneeberger Pages: 35

Brand: TSI Instruments Pages: 4

Brand: Sper scientific Pages: 56

Brand: U.S. Solid Pages: 30

OMCL-AC240TS-R3

Brand: Olympus Pages: 3

Brand: LEGRAND Pages: 5

Digital Piano CA750

Brand: Kawai Pages: 76

Brand: Hanna Instruments Pages: 28

Brand: POSEIDON Pages: 13

Brand: Fluke Pages: 6

WTW SensoLyt 900

Brand: Xylem Pages: 12

Brand: Ralcam Pages: 8

Brand: ATD Tools Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands