Home
/
YOKOGAWA
/
ScopeCorder DL950
/
User Manual

YOKOGAWA ScopeCorder DL950, User Manual

Share

Page: 67 / 316

YOKOGAWA ScopeCorder DL950 User Manual Download Page 67

2-51

IM DL950-02EN

Input Setup (Setup)

2.

Tap

Setup

, or press the soft key. The following screen appears.

The items on the input setting screen vary depending on the installed modules and
measurement items. For details on the settings, see the explanation of the measurement
items in section 2.1 and later.

3.

Tap the items of each channel. Use the displayed list (options) or input box to set the items.

Input coupling

Turns waveform input on for all channels

Turns waveform input off for all channels

Turns the waveform input on or off

Display label

Vertical scale

Bandwidth limit

Probe attenuation, current-to-voltage conversion

ratio, or bridge voltage (for strain measurement)

Scroll to display channels

that do not fit in the screen.

Gauge factor (for strain measurement)

2.12 Displaying the All Channel Setup Menu

«
...
65
66
67
68
69
...
»

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands