manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 56

2-40

IM DL950-02EN

One-Shot Output Setup (One shot out Setup)

3.

 Tap 

One Shot Out Setup

, or press the soft key. The following screen appears.

CAN Frame One-Shot Output (for the 720240 (CAN MONITOR), 720241 (CAN & LIN) modules)

 

* Can only be set when Frame is set to Data.

Set the message format (STD, XTD).
Set the message ID.
Set the frame (Remote, Data).
Set the data area byte size (0 to 15).*

Set the data.

CAN or CAN FD Frame One-Shot Output (for the 720242 (CAN/CAN FD) module)

* Can only be set when Frame is set to Data.

Set the frame (Remote, Data).

You can set this only when the 

message type is CAN.

It is fixed to Data for CAN FD.

Set the message type 

(CAN, CAN FD).

Set the message format 

(STD, XTD).

Set the message ID.

Set the data area byte size (0 to 15).*

Data*

The number of transmission 

data bytes that can be set varies 

depending on the message type 

and DLC settings.

► Next page

2.9  Configuring the Monitoring of CAN and CAN FD Bus Signals (/VCE option)

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands