manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 170

11-2

IM DL950-02EN

11.1  Automatically Measuring Waveform 

Parameters

This section explains the following settings for automatically measuring waveform parameters:

Items Common to Scope Mode and Recorder Mode

•  Turning automated measurement on and off
•  Source waveform and measurement items
•  Delay settings
•  Turning period measurement on and off
•  Time measurement reference level
•  Measurement window and measurement time period

► “Automated Measurement of Waveform Parameters” in the Features Guide

MEASURE Menu

1.

  On the waveform screen’s MENU, tap 

ANALYSIS

 > 

MEASURE

, or press 

MEASURE

.

  

Set the measurement time period.

Set statistical processing to OFF.

Continuous ► sec.11.2. Cycle ► sec. 11.3. History 

► sec. 11.4.

Turns automated measurement on or off

See “Setting the Source Waveform and 

Measurement Items.”

See “Setting the Time Measurement 

Reference Level and 1-Cycle Mode.”

See “Setting the Indicator.”

See “Setting Measurement Time 

Period 2.”

When Dual Capture Mode Is Off

When Dual Capture Mode Is On

See “During Dual Capture.”

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands