manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 133

6-5

IM DL950-02EN

Measuring X-Y Waveforms with Horizontal Cursors (Horizontal)

3.

 Tap 

Type

, or press the soft key to select 

Horizontal

.

  

See “Setting Measurement Items.”

Set the cursor positions (Cursor1: Y1, Cursor2: Y2).

You can also drag the cursors on the X-Y screen. Tap the cursor and 

then tap the arrow that appears (shown in the figure below) to adjust 

the cursor position in fine increments.

Select the trace to measure with cursors (XY1 to XY8).

Set the cursor type to Horizontal (horizontal).

Set Mode to ON.

Setting Measurement Items (Item Setup)

4.

 Tap 

Item Setup

, or press the soft key. The following screen appears.

  

Select the measurement items that you want to use.

Y1: Vertical (Y axis) value at Cursor1

Y2: Vertical (Y axis) value at Cursor2

ΔY: Difference between the vertical (Y axis) values of 

Cursor1 and Cursor2

6.3  Measuring X-Y Waveforms with Cursors

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands