YOKOGAWA ScopeCorder DL950 User Manual Download Page 155

Page: 155 / 316

9-3

IM DL950-02EN

Note

• After you execute a search on the history waveforms, the only waveforms that are displayed are those

that meet the search conditions. To display all the history waveforms in acquisition memory again, turn

the history waveform search feature off.

• The averaging feature requires a certain amount of acquisition memory. If this is not available, you will

not be able to display the Average Record.

Displaying a List of History Waveforms (List)

Tap

List

, or press the soft key. A list of history waveforms appears.

Date

List of history waveforms

Record number

Timestamp (time reference time information)

Note

Notes on Using the History Feature

• When the acquisition mode is set to Average, you cannot use the history feature.

• If you stop waveform acquisition, even if one complete screen’s worth of waveform data has not been

acquired, the waveform at which the trigger occurred is displayed as a single history waveform.

• You can start waveform acquisition when the History menu is displayed. However, you cannot change

the history feature settings while waveform acquisition is in progress.

• The settings are restricted so that the following relationship is retained: Last record (End Record) ≤

Selected Record ≤ first record (Start Record).

• When you load waveform data from the specified storage device, history waveforms up to that point are

cleared. The loaded waveform data is placed in record number zero. If you load a file containing multiple

history waveforms, the latest waveform is placed in zero, and earlier waveforms are placed in order to

record numbers –1, –2, and so on.

• Computation and automated measurement of waveform parameters are performed on the waveform

of the record number specified by Selected Record. You can analyze old data as long as you do not

overwrite the acquisition memory contents by restarting waveform acquisition. If Display Mode is set to

Average Record, analysis is performed on the averaged waveform.

• History waveforms are cleared when you turn the power off.

9.1 Displaying Waveform History Waveforms

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL950, User Manual

Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands