YOKOGAWA ScopeCorder DL950 User Manual Download Page 91

Page: 91 / 316

4-3

IM DL950-02EN

SingleN:

The instrument acquires signals each time the trigger conditions are met until a

specified number of signals have been acquired, stops acquisition, and displays

all of the acquired signals. If no triggers occur, the display is not updated.

On Start:

Regardless of the trigger settings, when you press the START key, the instrument

updates the displayed waveforms once and stops signal acquisition. If the time

axis is set to a value that would cause the display to switch to roll mode, roll

mode display will be enabled. When data has been acquired up to the amount

specified by the set record length, the waveform display stops.

4.1 Setting the Trigger Mode

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL950, User Manual

Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands