manualshive.com logo in svg

Vanderbilt SPC4 Series, Installation & Configuration Manual, Page: 206 / 402

Share
Download
Vanderbilt SPC4 Series Installation & Configuration Manual Download Page 206

Using Code

Using Caller
ID

Action

Response

**** XA1.ON

****.XA1.ON

Where X10 device is identified as
“A1”, it is triggered on.

Status of “A1”

**** XA1.OFF

****.XA1.OFF

Where X10 device is identified as
“A1”, it is triggered off.

Status of “A1”

**** LOG

****.LOG

Up to 10 recent events are displayed.

Recent events

**** ENGA.ON

****.ENGA.ON

ENGA.ON

Enable Engineer access.

Allow Engineer

**** ENGA.OFF

****.ENGA.OFF

ENGA.OFF

Disable Engineer access.

Revoke Engineer

**** MANA.ON

****.MANA.ON

Enable Manufacturer access.

Manufacturer status

**** MANA.OFF

****.MANA.OFF

Disable Manufacturer access.

Manufacturer status

**** O5.ON

****.O5.ON

****.OUTPUT

Where output (mapping gate) is
identified as “O5”, it is triggered on.

Status of “O5”

For example:

l

Output O5 on.

l

Output heating on
(where heating is the
name of the output).

**** O5.OFF

****.O5.OFF

Where output (mapping gate) is
identified as “O5”, it is triggered off.

Status of “O5”

For example: Output O5 off

****.CLR

****.RESTORE

Allows clear alerts by SMS.

For SMS recognition, output (mapping gate) identification uses the format ONNN, where O stands
for output, and NNN are the numeric placeholders, of which not all are necessary.
(Example: O5 for output 5)

For SMS recognition, X-10 device uses the format: XYNN, where X stands for X-10; Y stands for
the alphabetic identity and NN are the available numeric placeholders. (Example: XA1)

The SMS operates using a standard protocol that is used in SMS telephones. Note that some PSTN
operators do not provide the service of SMS over PSTN. For SMS to operate over PSTN, the following
criteria are required:

l

Caller ID needs to be enabled on the telephone line.

l

Direct telephone line – not through PABX or other communications equipment.

l

Also note that most Service Providers only allow SMS to a telephone registered in the same
country. (This is due to billing issues.)

SPC4xxx/5xxx/6xxx – Installation & Configuration Manual

Engineer programming via the browser

© Vanderbilt 2018

206

A6V10276959-d

11.2018

Summary of Contents for SPC4 Series



















































































































































































































































































































































































































Reviews:

No comments