manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Service Manual

The Suzuki Swift RS415 2017 Service Manual is available for free download on manualshive.com. This comprehensive manual includes detailed instructions and diagrams for vehicle maintenance and repairs. Get your hands on this essential manual to ensure your Suzuki Swift stays in top condition. Download it now!

Share
Download
background image

0B-7 Maintenance and Lubrication: 

Fuel Filter Replacement

S4RS0A0206042

WARNING:

This work must be performed in a well 
ventilated area and away from any open 
flames (such as gas hot water heaters).

 

Fuel filter is installed in fuel pump assembly in fuel tank.
Replace fuel filter or fuel pump assembly with new one, 
referring to “Fuel Pump Assembly Removal and 
Installation:  in Section 1G” for proper procedure.

Fuel Tank Inspection

S4RS0A0206012

Check fuel tank damage, cracks, fuel leakage, corrosion 
and tank bolts looseness.
If a problem is found, repair or replace.

PCV Valve Inspection

S4RS0A0206013

Check crankcase ventilation hose and PCV hose for 
leaks, cracks or clog, and PCV valve for stick or clog. 
Refer to “PCV Valve Inspection:  in Section 1B” for PCV 
valve checking procedure.

Fuel Evaporative Emission Control System 
Inspection

S4RS0A0206014

1) Visually inspect hoses for cracks, damage, or 

excessive bends. Inspect all clamps for damage and 
proper position.

2) Check EVAP canister for operation and clog, 

referring to “EVAP Canister Inspection:  in Section 
1B”.
If a malfunction is found, repair or replace.

Brake Discs and Pads (Front) Inspection

S4RS0A0206015

1) Remove wheel and caliper but don’t disconnect 

brake hose from caliper.

2) Check front disc brake pads and discs for excessive 

wear, damage and deflection. Replace parts as 
necessary. For details, refer to “Front Disc Brake 
Pad Inspection:  in Section 4B” and “Front Brake 
Disc Inspection:  in Section 4B”.
Be sure to torque caliper pin bolts to specification.

Brake Drums and Shoes (Rear) Inspection

S4RS0A0206016

1) Remove wheel and brake drum.
2) Check rear brake drums and brake linings for 

excessive wear and damage, while wheels and 
drums are removed. At the same time, check wheel 
cylinders for leaks. Replace these parts as 
necessary.
For details, refer to “Rear Brake Drum and Shoe 
Inspection:  in Section 4C” and “Rear Brake Shoe 
Inspection:  in Section 4C”.

I4RS0A020019-

I4RS0A020006-

I3RM0A020006-

I4RS0A020007-

Summary of Contents for SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SWIFT RS415 2017

Lancia THESIS CONNECT Owner'S Handbook Manual preview
THESIS CONNECT
Brand: Lancia Pages: 386
MASCOT SMARTCHARGER User Manual preview
SMARTCHARGER
Brand: MASCOT Pages: 12
Cadillac 2009 CTS Personalization Manual preview
2009 CTS
Brand: Cadillac Pages: 20
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Brand: Thule Pages: 12
Renault CAPTUR 2019 Vehicle Instruction Card preview
CAPTUR 2019
Brand: Renault Pages: 11
Xforce PR-104 User Manual preview
PR-104
Brand: Xforce Pages: 11
Macally MAGME User Manual preview
MAGME
Brand: Macally Pages: 10
Lexus IS220d 2011 Manual preview
IS220d 2011
Brand: Lexus Pages: 609
Fortin Electronic Systems EVO-CAN Suggested Wiring Configuration preview
EVO-CAN
Brand: Fortin Electronic Systems Pages: 5
Jeep 2018 GRAND CHEROKEE User Manual preview
2018 GRAND CHEROKEE
Brand: Jeep Pages: 372
Safe Fleet PRIME DESIGN HRR-NV11B Manual preview
PRIME DESIGN HRR-NV11B
Brand: Safe Fleet Pages: 12
Honda 1996 Civic Del Sol Owner'S Manual preview
1996 Civic Del Sol
Brand: Honda Pages: 219
Whispbar K665 Manual preview
K665
Brand: Whispbar Pages: 31
Ferrari GTC 4 Lusso Roadside Assistance Manual preview
GTC 4 Lusso
Brand: Ferrari Pages: 45
Adaptiv Mini CAM-MB7-AD User Manual preview
Mini CAM-MB7-AD
Brand: Adaptiv Pages: 4
Baja Designs 448024 Manual preview
448024
Brand: Baja Designs Pages: 2
Peiying PY-EM01 Owner'S Manual preview
PY-EM01
Brand: Peiying Pages: 28
Kia Forte 2021 Features & Functions Manual preview
Forte 2021
Brand: Kia Pages: 54

Brands by name

Popular brands

Load more brands