Suzuki SWIFT RS415 2017 Service Manual Download Page 681 | Manualshive

Page: 681 / 1257

background image

Automatic Transmission: 5A-141

Valve Body Assembly Disassembly and
Reassembly

S4RS0A5106051

CAUTION:

When replacing pressure control solenoid
valve and/or TCC pressure control solenoid
valve, it is strictly required to replace it
together with valve body assembly as a set.
Replacing pressure control solenoid valve
and/or TCC pressure control solenoid valve
independently may cause excessive shift
shock.

Disassembly

1) Pull out manual valve (1).

2) Remove pressure control solenoid valve (1).

3) Remove TCC pressure control solenoid valve (1).

4) Remove shift solenoid valve-A (1).

5) Remove shift solenoid valve-B (1).

6) Remove timing solenoid valve (1).

7) Remove temperature sensor clamp (1).

2. Solenoid lock plate

I2RH0B510216-

I2RH0B510217-

1

I4RS0A510045-

I2RH0B510219-

I2RH0B510220-

I2RH0B510221-

I2RH0B510222-

«
...
679
680
681
682
683
...
»

Summary of Contents for SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SWIFT RS415 2017

Brand: iDataLink Pages: 106

FleetMaster Air FW8 Series

Brand: SAF-HOLLAND Pages: 20

Brand: Safe Fleet Pages: 38

Brand: Tessera4x4 Pages: 20

Brand: SnapPad Pages: 5

Brand: Cadillac Pages: 407

Brand: Caltrend Pages: 3

Brand: Weltmann KFZ-Teile Pages: 12

Brand: Acura Pages: 6

Brand: travall Pages: 4

Brand: TAUBENREUTHER Pages: 18

Brand: Curtis Pages: 6

Brand: Car-Interface Pages: 23

Omni-Bike Sport Ducato

Brand: OMNISTOR Pages: 5

Brand: Volkswagen Pages: 68

PRO-FLO XT 3527

Brand: Edelbrock Pages: 39

Brand: Uniden Pages: 16

Brand: Altius Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands