Suzuki SWIFT RS415 2017 Service Manual Download Page 424

Page: 424 / 1257

2B-14 Front Suspension:

NOTE:

• Before installing bushing, apply soap

water on its circumference to facilitate
installation.

2) Press-fit bushing (1) so that dimensions and in figure

become equal.

Suspension Control Arm / Steering Knuckle
Check

S4RS0A2206015

Inspect for cracks, deformation or damage.
If defective, replace.

Suspension Control Arm Bushing Check

S4RS0A2206016

Inspect for damage, wear or deterioration.
If defective, replace.

Suspension Control Arm Joint Check

S4RS0A2206017

• Check for smooth rotation.
• Inspect ball stud for damage.
• Inspect dust cover for damage.

NOTE:
Suspension control arm and arm joint cannot
be separated.

If there is any damage to either, control arm assembly
must be replaced as a complete unit.

(A)

(B)

I4RS0A220032-

I4RS0A220033-

I2RH01220005-

I4RS0A220035-

I4RS0A220036-

Summary of Contents for SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SWIFT RS415 2017

Reviews:

Related manuals for SWIFT RS415 2017

Brands by name

Popular brands

Suzuki SWIFT RS415 2017, Service Manual

Search results

Summary of Contents for SWIFT RS415 2017

Reviews:

Related manuals for SWIFT RS415 2017

Brands by name

Popular brands