IN ADDITION TO THE OTHER WARNINGS IN THIS MANUAL
OBSERVE THE FOLLOWING FOR SAFE OPERATION:
l
Respect your Stanley pneumatic fastening tool as a tool. It
is not a toy. No Horseplay.
l
Use the Stanley pneumatic tool only for the purpose for
which it was designed.
l
Never use the tool in a manner that could cause a
fastener to be directed towards the user or others in the
work area.
l
Do not use the tool as a hammer.
l
Always carry the tool by the handle. Never carry the
tool by the air hose. Never carry the tool with the trigger
pulled.
l
Do not alter or modify this tool from the original design or
function without the written approval of Stanley Inc.
l
Always be aware that misuse and improper handling of this
tool can cause injury to yourself and others.
l
Never clamp or tape the trigger or safety trip in an
actuated position.
l
Never leave a tool unattended with the air hose attached.
l
Do not operate this tool if it does not contain a legible
WARNING LABEL.
l
Do not continue to use a tool that leaks air or does not
function properly. Notify your nearest Stanley stockist if
your tool continues to experience functional problems.
l
During operation, hold the tool in such a way that no
injuries can be caused to the head or to the body should
the tool recoil increase due to a drop in the supply air
pressure or hard areas within the work piece.
l
Do not work close to corners or at the edge of the work
piece. The fastener could slip out of the work piece,
possibly causing injury.
l
When transporting the tool, disconnect the air supply first.
l
Check that the safety trip (if present) and the trigger both
function correctly.
l
Do not dismantle or block any part of the tool, in particular
not the safety trip.
l
Never perform “emergency repairs” without the proper
equipment.
l
Avoid weakening the tool by punching or engraving.
MAINTENANCE
Disconnect the tool from the air supply and completely empty
the magazine before starting maintenance or repairs. Note the
warnings in this manual in the Tool Technical Data and on the
tool itself and use extra care when evaluating problem tools.
Stanley replacement parts are recommended. Do not use
modified parts or parts that will not give performance equal to
the original equipment.
When repairing a tool, make sure the internal parts are
clean and lubricated. Use Parker “O”-Lube or equivalent
on all “O”-rings. Coat each “O”-ring with “O”-Lube before
assembling. Use a small amount of oil on all moving surfaces
and pivots.
NOISE EMISSION
(See Tool Technical Data)
The characteristic noise values for the tool have been
determined in accordance with EN 12549 - “Acoustics - Noise
test code for fastener driving tools - Engineering Method.”
These values are tool related characteristic values and do not
represent the noise development at the point of use.
INFORMATION ON VIBRATION
(see Tool Technical Data)
The characteristic vibration value for the tool has
been determined in accordance with ISO/WD 8662-11
“Measurement of vibration in hand held power tools - Part 11
Fastener Driving Tools”.
This value is a tool related characteristic and does not
represent the influence on the hand-arm system when using
the tool.
GB
©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this
document do not constitute CE compliance for the products.
F
©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées
de ce document ne signifient en rien que les produits soient conformes aux normes CE.
D
©Stanley Bostitch. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte
Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.
NL
©Stanley Bostitch. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige
kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.
DK
©Stanley Bostitch. Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument
udgør ikke CE overholdelse for produkterne.
SF
©Stanley Bostitch. Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt
kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.
G
©Stanley Bostitch. Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη
εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για
τα προϊόντα.
I
©Stanley Bostitch. Vietata la riproduzione senza permesso. Le copie non autorizzate di questo
documento non garantiscono la conformità CE per i relativi prodotti.
N
©Stanley Bostitch. Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette
dokumentet oppfyller ikke kravene for CE-merking for produktet.
P
©Stanley Bostitch. Reprodução proibida sem autorização prévia. As cópias não autorizadas
deste documento não estão em conformidade com a CE para os produtos.
E
©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
documento no suponen la conformidad con las normas CE de los productos.
S
©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
documento no suponen la conformidad con las normas CE de los productos.
PL
©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
prezentowanych produktów.
CZ
©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
prezentowanych produktów.
SK
©Stanley Bostitch. Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto
dokumentu nie sú v súlade s CE pre dané výrobky.
HU
©Stanley Bostitch. A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül
sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.
