Siemens FC300 Operating Instructions Manual Download Page 60 | Manualshive

Page: 60 / 518

Siemens FC300 Operating Instructions Manual Download Page 60

WARNING

Connecting device in energized state
Risk of explosion in hazardous areas.
● Connect devices in hazardous areas only in a de-energized state.
Exceptions:
● Devices having the type of protection "Intrinsic safety Ex i" may also be connected in

energized state in hazardous areas.

● Exceptions for type of protection "Non-sparking nA" (Zone 2) are regulated in the relevant

certificate.

WARNING

Incorrect selection of type of protection
Risk of explosion in areas subject to explosion hazard.
This device is approved for several types of protection.
1. Decide in favor of one type of protection.
2. Connect the device in accordance with the selected type of protection.
3. In order to avoid incorrect use at a later point, make the types of protection that are not

used permanently unrecognizable on the nameplate.

Note
Electromagnetic compatibility (EMC)
You can use this device in industrial environments, households and small businesses.
For metal housings there is an increased electromagnetic compatibility compared to high-

frequency radiation. This protection can be increased by grounding the housing, see Basic

safety notes (Page 57).

Note
Improvement of interference immunity
● Lay signal cables separate from cables with voltages > 60 V.
● Use cables with twisted wires.
● Keep device and cables at a distance from strong electromagnetic fields.
● Take account of the conditions for communication specified in the Technical data

(Page 215).

● HART: Use shielded cables to guarantee the full specification according to HART.

Connecting
5.1 Basic safety notes

MASS 2100 & FC300 (FCT030)

60

Operating Instructions, 06/2017, A5E39789040-AA

«
...
58
59
60
61
62
...
»

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments