Siemens FC300 Operating Instructions Manual Download Page 201

Page: 201 / 518

ID/

Icons

Diagnostic

Action

Comment

155

CH1

Loop current deviation. Check current output

cable connection. In passive mode check pow‐

er supply.

156

Safety validation state

Finish proof test and confirm proof test passed,

or select skip proof test in menu "Functional

safety"

157

Functional safety

Device detected an event in safe operation. Ac‐

knowledge the safety event in menu Functional

Safety and repeat the safety commissioning. If

the error still exists, contact your local Siemens

representative.

158

CH1

Cable break. Check current output cable con‐

nection

159

Internal error

Internal error in transmitter. Turn off the power,

wait 5 seconds and turn on the power again. If

the error still exists, contact your local Siemens

representative.

160

Mass flow

Value simulated. Disable 'Simulation' before re‐

turning to normal operation

161

Volume flow

Value simulated. Disable 'Simulation' before re‐

turning to normal operation

162

Density

Value simulated. Disable 'Simulation' before re‐

turning to normal operation

163

Medium temperature

Value simulated. Disable 'Simulation' before re‐

turning to normal operation

Diagnosing and troubleshooting

10.2 Fault codes and corrective actions

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

201

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Search results

Summary of Contents for FC300

Reviews:

Siemens FC300, Operating Instructions Manual, Page: 201 / 518

Search results

Summary of Contents for FC300

Reviews: