Home
/
Siemens
/
FC300
/
Operating Instructions Manual

Siemens FC300, Operating Instructions Manual, Page: 151 / 518

Share

Page: 151 / 518

Siemens FC300 Operating Instructions Manual Download Page 151

● Direction = Positive
● Frequency Value High = 12 kHz
● Frequency Value Low = 2 kHz
● Flow Value High = 15 kg/s
● Flow Value Low = 5 kg/s
Measured massflow value = 7.5 kg/s (constant)
Result:
● Frequency = 4.5 kHz

Note
The connected equipment must be capable of registering the full range of frequencies

configured.

8.6.4

Redundancy mode (frequency)

8.6.4.1

Redundancy mode

If both channel 2 and channel 3 are configured as frequency outputs, channel 3 can be

configured for redundancy mode to follow channel 2 shifted by 90˚or 180˚. If set to redundancy

mode, channel 3 inherits all channel 2 settings. The flow direction will determine whether

channel 3 is shifted before or after channel 2 at 90° shift.
The following examples describe the frequency functionalities for channel 2 and 3 in

redundancy mode:

Channel 2 configured as positive direction and channel 3 set to redundancy mode 90°

Figure 8-8

Positive flow - channel 3 leads by 90°

Figure 8-9

Negative flow - channel 3 lags by 90°

Functions

8.6 Inputs and outputs

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

151

«
...
149
150
151
152
153
...
»

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments