manualshive.com logo in svg

Siemens FC300, Operating Instructions Manual, Page: 238 / 518

Share
Download
Siemens FC300 Operating Instructions Manual Download Page 238

Viscosity [cSt]

Figure 11-9 MASS 2100 DI 15

11.9

Bus communication

Table 11-27 HART, MODBUS and Profibus communication   

Description

Specification

More information

Manufacturer ID

42 (2A Hex)

Manufacturer ID parameter

Device ID

34 (22 Hex)

Device type parameter

HART protocol revision

7.5

HART protocol revision parameter

Profibus profile

4.0

Profibus protocol revision parameter

Modbus RS485 RTU

-

-

Number of device variables

11

Number of process values, both measured 

and derived

Physical layers supported

FSK

Frequency Shift Keyed

Loop-powered

No

4-wire device

Note
Always refer to nameplates on the device for device-specific approvals.

Technical data
11.9 Bus communication

MASS 2100 & FC300 (FCT030)

238

Operating Instructions, 06/2017, A5E39789040-AA

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments