manualshive.com logo in svg

Siemens FC300, Operating Instructions Manual, Page: 187 / 518

Share
Download
Siemens FC300 Operating Instructions Manual Download Page 187

Icon

Name

Description

Memory card

Capacity is 75 % used

Memory card

Capacity is 100 % used

The table explains the meaning of possible device status and actions for the user or service. 

Depending on the type and availability of local display of the device, status is shown as 

SIMATIC and/or NAMUR NE107 symbol. Additionally the symbol for the according device 

status is visualized in remote engineering, asset management or process control systems. 

Refer to the manual of your automation system how diagnostics states are displayed.

Symbols

Table 10-1

Mapping of device states in SIMATIC products (e.g. SIMATIC PDM) and NE107

SIMATIC PDM / PLC

NAMUR NE 107

Description
 

Measure
 

Icon

Device 

status

Pri‐

ority

Icon

Device 

status

Pri‐

ority

Mainte‐

nance 

alarm

1

Failure

1

Output signal invalid due to malfunc‐

tion in the field device or its peripher‐

als.

Maintenance is required 

immediately.

Mainte‐

nance de‐

manded
 

2

Mainte‐

nance re‐

quired

3

Output signal is still valid but wear re‐

serve is nearly exhausted, or a func‐

tion will soon be restricted. 

Maintenance is strongly 

recommended as soon as 

possible.

Mainte‐

nance re‐

quired

3

Mainte‐

nance re‐

quired

3

Output signal is still valid. No func‐

tional restriction has been detected 

but wear reserve is expected in the 

next weeks.

Maintenance of device 

should be planned.

Manual 

mode

4

Function 

check

2

Output signal temporarily invalid (e.g. 

frozen) due to ongoing work on the 

device.

Disable manual mode via 

HMI or engineering sys‐

tem.

Simula‐

tion mode

5

Function 

check

2

Output signal temporarily does not 

represent the process because out‐

put based on a simulation value.

Disable simulation mode 

via HMI or engineering 

system or restart device.

Out of 

service

6

Function 

check

2

Output signal does not represent 

process value. 
Device mode is set to "Out of service".

Disable “Out of service” 

and activate normal opera‐

tion mode.

Configura‐

tion error

7

Failure

1

Output signal invalid due to a param‐

eter setting, an interconnection error 

or a configuration error in HW.

Check device hardware 

configuration or parameter 

settings via HMI or engi‐

neering system.

Diagnosing and troubleshooting

10.1 Device status symbols

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

187

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments