Home
/
Siemens
/
FC300
/
Operating Instructions Manual

Siemens FC300, Operating Instructions Manual, Page: 141 / 518

Share

Page: 141 / 518

Siemens FC300 Operating Instructions Manual Download Page 141

8.5

Process noise damping

Noise damping function

The dynamic sensitivity of the flow measurement signal to rapid changes in process flows can

be reduced by use of the process noise damping function. The function is typically used in

environment with:
● Strongly pulsating flow
● Changing pump speeds
● Large pressure variations

Process noise damping settings

Reduce interfering process noise by increasing the setting of the parameter "Process Noise

Damping".
● Centrifugal pump (1: low)
● Triplex pump (2)
● Duplex pump (3)
● Simplex pump (4)
● Cam pump (5: high)
The default value is "Duplex pump". The damping affects all functions and outputs of the sensor.

Figure 8-2

Centrifugal pump (1: low)

Figure 8-3

Triplex pump (2)

Functions

8.5 Process noise damping

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

141

«
...
139
140
141
142
143
...
»

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments