manualshive.com logo in svg

Siemens FC300, Operating Instructions Manual, Page: 204 / 518

Share
Download
Siemens FC300 Operating Instructions Manual Download Page 204

ID/

Icons

Diagnostic

Action

Comment

186

CH3

Input current too low. Check wiring and signal 

of connected sensor or output source to input 

channel

If Operation mode is config‐

ured to Current input

187

CH3

Input current too high. Check wiring and signal 

of connected sensor or output source to input 

channel

If Operation mode is config‐

ured to Current input

188

CH3

External failure. Connected sensor or output to 

input channel is out of operation range. Please 

check connected sensor or output source.

If Operation mode is config‐

ured to Current input

189

CH4

Input current too low. Check wiring and signal 

of connected sensor or output source to input 

channel

If Operation mode is config‐

ured to Current input

190

CH4

Input current too high. Check wiring and signal 

of connected sensor or output source to input 

channel

If Operation mode is config‐

ured to Current input

191

CH4

External failure. Connected sensor or output to 

input channel is out of operation range. Please 

check connected sensor or output source.

If Operation mode is config‐

ured to Current input

192

Dosing

Dosing time overrun. Check installation. If ok, 

increase 'Duration Time'

 

193

Dosing

Dosing quantity overrun. Check installation. If 

ok, decrease 'Overrun Value'

 

194

Dosing

Invalid process value during dosing. Check in‐

stallation for abnormal operating conditions. If 

the error still exists, contact your local Siemens 

representative.

 

Diagnosing and troubleshooting
10.2 Fault codes and corrective actions

MASS 2100 & FC300 (FCT030)

204

Operating Instructions, 06/2017, A5E39789040-AA

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments