Siemens FC300 Operating Instructions Manual Download Page 441

Page: 441 / 518

HMI menu ID Parameter

Description

Default value

[unit]

Value range

Access

level

3.4.3.2.3

Error status

Error status - Current

● Upper

saturation

● Lower

saturation

● Fail-safe

behaviour
avtive

● Cable breal
● Loop current

deviation

Read

only

3.4.3.2.4

Pulse counter

Actual value of output pulses.

Read

only

3.4.3.2.5

Reset pulse counter

Status of the reset pulse counter

Read

only

3.4.3.3

Channel 3 – input/output

3.4.3.3.1

Operation mode

Set the output functionality you

want the channel to operate.

Status output

● Off
● Current output
● Frequency

output

● Pulse output
● Status output

Read

only

3.4.3.3.2

Digital input value

Select the digital input value

Read

only

3.4.3.3.2

Totalized amount

Actual value of totalized amount. [kg]

Read

only

3.4.3.3.2

Output frequency

Actual value of frequency output. [Hz]

Read

only

3.4.3.3.2

Digital output signal

Actual value of status output.

Read

only

3.4.3.3.2

Loop current

Actual value of current output

[mA]

Read

only

3.4.3.3.3

Error status

Error status - pulse

● Upper

saturation

● Fail-safe

behaiviour
active

Read

only

3.4.3.3.3

Error status

Error status - frequency

● Upper

saturation

● Lower

saturation

● Fail-safe

behaiviour
active

Read

only

Default settings

B.9 Maintenance and diagnostics

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

441

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Search results

Summary of Contents for FC300

Reviews:

Siemens FC300, Operating Instructions Manual, Page: 441 / 518

Search results

Summary of Contents for FC300

Reviews: