Siemens FC300 Operating Instructions Manual Download Page 81 | Manualshive

Page: 81 / 518

Siemens FC300 Operating Instructions Manual Download Page 81

5.2.4.9

Step 5: Finishing the transmitter connection

Connection check-up

1. Check individual wire installation by tugging firmly.
2. Firmly tighten cable glands and insert blanking plugs in unused cable entries.
3. Remove O-ring from lid.
4. Reinstate lid and screw in until mechanical stop. Wind back lid by one turn.
5. Mount O-ring by pulling it over the lid and tighten lid cover until you feel friction from the O-

ring on both sides. Wind lid further by one quarter of a turn to seal on the O-ring.

6. Reinstate and tighten lid lock screw.
7. Ensure that moisture does not penetrate to inside of electronics housing by creating a drip

loop (bend cables downward) immediately before cable glands.

Connecting

5.2 Connecting MASS 2100/FC300

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

81

«
...
79
80
81
82
83
...
»

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments