Siemens FC300 Operating Instructions Manual Download Page 207

Page: 207 / 518

ID/

Icons

Diagnostic

Action

Comment

214

CH2

Channel simulated. Disable 'Simulation' before

returning to normal operation

215

CH3

Channel simulated. Disable 'Simulation' before

returning to normal operation

216

CH4

Channel simulated. Disable 'Simulation' before

returning to normal operation

217

Process values frozen

All process values and totalizers are frozen. To

return to normal operation the related input sig‐

nal has to switch.

218

Outputs forced

Outputs are forced. To return to normal opera‐

tion the related input signal has to switch

219

CH2

Loop current deviation. Check current output

cable connection. In passive mode check pow‐

er supply.

If Operation mode is config‐

ured to Current output

220

CH3

Loop current deviation. Check current output

cable connection. In passive mode check pow‐

er supply.

If Operation mode is config‐

ured to Current output

221

CH4

Loop current deviation. Check current output

cable connection. In passive mode check pow‐

er supply.

If Operation mode is config‐

ured to Current output

222

Modbus

Invalid register mapping. Source register allo‐

cated in duplicate. Check register mapping.

Diagnosing and troubleshooting

10.2 Fault codes and corrective actions

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

207

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Search results

Summary of Contents for FC300

Reviews:

Siemens FC300, Operating Instructions Manual, Page: 207 / 518

Search results

Summary of Contents for FC300

Reviews: