manualshive.com logo in svg

Siemens FC300, Operating Instructions Manual, Page: 145 / 518

Share
Download
Siemens FC300 Operating Instructions Manual Download Page 145

,

$

>P$@

)&

S>@

①

Linear control range

②

Measuring range lower limit

③

Measuring range upper limit

④

Lower fault current value

⑤

Recommended setting range for lower fault current

⑥

Recommended setting range for upper fault current

⑦

Measuring range

Figure 8-7

Current limits for NAMUR configuration

The fail safe current output signal can be selected to:
● Minimum Current (defined in the Current Mode selection)
● Maximum Current (defined in the Current Mode selection)
● Last Good Value (the last process value before the failure occurred)
● Current Value (actual measured value)
● User defined (within the range of 0 mA to 25 mA 

1)

)

1)

 For channel 1 the range is 3.5 mA to 25 mA

In the alarms lists inSensor diagnostic events (Page 189) it is listed which alarms bring the 

output to fail safe current.

Output scaling configuration

Below are four examples describing configuration possibilities for a current output.

Functions

8.6 Inputs and outputs

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

145

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments