manualshive.com logo in svg

Siemens FC300, Operating Instructions Manual, Page: 189 / 518

Share
Download
Siemens FC300 Operating Instructions Manual Download Page 189

10.2.1

Sensor diagnostic events

Sensor diagnostic events

ID/

Icons

Diagnostic

Action

Comments

32

SIL parameters not validated

Run the 'Safety Validation' wizard to validate the 

safety-critical parameters. The device can be 

put into Safe Operation mode after validation

 

33

SIL parameters not validated

Run the 'Safety Validation' wizard to validate the 

safety-critical parameters. The device can be 

put into Safe Operation mode after validation

 

34

SIL parameters not validated

Run the 'Safety Validation' wizard to validate the 

safety-critical parameters. The device can be 

put into Safe Operation mode after validation

 

35

SIL parameters not validated

Run the 'Safety Validation' wizard to validate the 

safety-critical parameters. The device can be 

put into Safe Operation mode after validation

 

36

Sensor supply volt. out of range Contact your local Siemens representative

 

37

Sensor supply volt. out of range Contact your local Siemens representative

 

38

Temperature measurement fault Turn off the power, wait 5 seconds and turn on 

the power again. If the failure continues then 

contact your local Siemens representative

 

39

Temperature measurement fault Turn off the power, wait 5 seconds and turn on 

the power again. If the failure continues then 

contact your local Siemens representative

 

Diagnosing and troubleshooting

10.2 Fault codes and corrective actions

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

189

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments