Siemens FC300 Operating Instructions Manual Download Page 203

Page: 203 / 518

ID/

Icons

Diagnostic

Action

Comment

176

Sensor

Sensor type incompatible. Please replace sen‐

sor.

177

Device is starting

Please wait until startup is finished. Startup time

see manual.

178

Transmitter

FW invalid. A component does not have the ex‐

pected FW version. Start a product firmware

update to update the component version.

179

Alarm class

Alarm class simulated. Disable Simulation be‐

fore returning to normal operation.

No detailed information avail‐

able in view Active diagnostic

events. Icon depends on simu‐

lated alarm class resp. NA‐

MUR status signal and the pri‐

ority in case of multiple alarm

classes simulated.

181

SensorFlash

SensorFlash Chkdsk failed. Start Chkdsk

again. If error still exist replace SensorFlash.

182

Communication interface

FW invalid. A component does not have the ex‐

pected FW version. Start a product firmware

update to update the component version or re‐

place the component.

183

CH2

Input current too low. Check wiring and signal

of connected sensor or output source to input

channel.

If Operation mode is config‐

ured to Current input.

184

CH2

Input current too high. Check wiring and signal

of connected sensor or output source to input

channel.

If Operation mode is configur‐

edto Current input

185

CH2

External failure. Connected sensor or output to

input channel is out of operation range. Please

check connected sensor or output source.

If Operation mode is config‐

ured to Current input

Diagnosing and troubleshooting

10.2 Fault codes and corrective actions

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

203

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Search results

Summary of Contents for FC300

Reviews:

Siemens FC300, Operating Instructions Manual, Page: 203 / 518

Search results

Summary of Contents for FC300

Reviews: