Siemens FC300 Operating Instructions Manual Download Page 423

Page: 423 / 518

HMI menu ID Parameter

Description

Default value

[unit]

Value range

Access

level

3.1.15.4

Order number

Replacement transmitter order

number (MLFB). Also shown on

the device nameplate.

Read

only

3.1.15.5

Comm. Interface HW

version

Comm. interface HW version

Read

only

Table B-32

Local display

HMI menu ID Parameter

Description

Default value

[unit]

Value range

Access

level

3.1.16.1

HW version

Local display hardware version.

Read

only

3.1.16.2

FW version

Local display firmware version.

Read

only

3.1.16.3

HMI cfg. version

HMI configuration file

Read

only

3.1.16.4

Order number

Replacement transmitter order

number (MLFB). Also shown on

the device nameplate.

Read

only

Table B-33

Diagnostic events

HMI menu ID Parameter

Description

Default value

[unit]

Value range

Access

level

3.2.1

Active diagnostic events Active diagnostic events

3.2.2

Diagnostic log

3.2.3

Clear diagnostic log

3.2.4

Acknowledge mode

Select manual or automatic ac‐

knowledge of alarms. Manual:

Acknowledge in alarm list view.

Automatic: when cause is gone.

Auto

● Manual
● Auto

3.2.5

Transmitter detailed

events

Transmitter detailed events

● DE10
● DE11
● DE12
● DE21
● DE22
● DE23
● DE24
● DE26
● DE27
● DE28
● DE29
● DE30
● DE31

Default settings

B.9 Maintenance and diagnostics

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

423

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Search results

Summary of Contents for FC300

Reviews:

Siemens FC300, Operating Instructions Manual, Page: 423 / 518

Search results

Summary of Contents for FC300

Reviews: